Vous pouvez télécharger le démo gratuit pour prendre un essai. Vous aurez plus confiance sur Pass4Test. N'hésitez plus à choisir la Q&A Juniper JN0-694 comme votre guide d'étude.
Le temps est tellement précieux dans cette société que une bonn façon de se former avant le test Juniper JN0-694 est très important. Pass4Test fait tous efforts à assurer tous les candidats à réussir le test. Aussi, un an de mise à jour est gratuite pour vous. Si vous ne passez pas le test, votre argent sera tout rendu.
Si vous choisissez notre l'outil formation, Pass4Test peut vous assurer le succès 100% du test Juniper JN0-694. Votre argent sera tout rendu si vous échouez le test.
Le produit de Pass4Test peut assurer les candidats à réussir le test Juniper JN0-694 à la première fois, mais aussi offrir la mise à jour gratuite pendant un an, les clients peuvent recevoir les ressources plus nouvelles. Pass4Test n'est pas seulement un site, mais aussi un bon centre de service.
Code d'Examen: JN0-694
Nom d'Examen: Juniper (Enterprise Routing and Switching Support, Professional (JNCSP-ENT))
Questions et réponses: 36 Q&As
JN0-694 Démo gratuit à télécharger: http://www.pass4test.fr/JN0-694.html
NO.1 You are troubleshooting a problem where an OSPF adjacency between two neighboring
routers will not form.
What are two reasons for this problem? (Choose two.)
A. One or both of the connected interfaces are missing the family inet statement.
B. One or both of the connected interfaces are missing the family iso statement.
C. The connected interfaces are not on the same subnet.
D. Another IGP is running on one or both of the routers, overriding OSPF.
Answer: B,D
Juniper JN0-694 JN0-694 JN0-694
NO.2 You observe that a router is using an unusually high amount of CPU cycles.
You determine that continuous SPF calculations in OSPF are being performed.
What are two reasons for this problem? (Choose two.)
A. The wrong authentication keys between the OSPF neighbors are used.
B. The interface MTU is mismatched between the OSPF neighbors.
C. There are duplicate router IDs within the OSPF area.
D. An OSPF adjacency is flapping.
Answer: C,D
Juniper JN0-694 JN0-694 examen JN0-694 JN0-694
NO.3 Your switch is experiencing a problem where a port that should have only one host connected
occasionally shows that multiple MAC addresses are being learned.
Which configuration setting would ensure that no extra hosts can join the network using this switch
port?
A. mac-limit
B. no-mac-learning
C. persistent-learning
D. bpdu-block-on-edge
Answer: D
Juniper JN0-694 JN0-694
NO.4 Your Junos device is dropping certain traffic flows, while allowing other traffic flows to pass
through the device unaffected.
Which CoS component is causing this problem?
A. BA classification
B. RED
C. MF classification
D. Rewrite rules
Answer: D
Juniper JN0-694 examen JN0-694 certification JN0-694 JN0-694 JN0-694
NO.5 You are implementing Q-in-Q tunneling on an EX Series switch. You want the tunnel to support
all C-VLANs; however, only some VLANs are able to send traffic across the tunnel.
Switch-1 has the following configuration:
[edit vlans]
user@Switch-1# show
v100 {
vlan-id 100;
interface {
ge-0/ 0/ 0.10;
ge-0/ 0/1.20;
}
dot1q-tunneling {
customer-vlans [ ];
}
}
What would solve this problem?
A. Add family ethernet-switching to the tunnel-side interface on Switch-1.
B. Implement RSTP .
C. Q-in-Q tunneling will not work in this scenario; use a Layer 2 VPN instead.
D. Remove the customer-vlans statement.
Answer: C
Juniper JN0-694 JN0-694 examen
NO.6 You are having problems redistributing RIP routes into OSPF. Your Junos device has the
following configuration:
[edit protocols ospf]
user@router# show
import my-policy;
area 0.0.0.0 {
interface ge-0/ 0/ 0.0;
interface ge-0/ 0/ ;
interface ge-0/ 0/ {
passive;
}
}
What would resolve the problem?
A. Apply my-policy as an export policy under the [edit protocols rip] hierarchy.
B. Apply my-policy as an import policy under the [edit protocols rip] hierarchy.
C. Apply my-policy as an export policy under the [edit protocols ospf] hierarchy.
D. Use the area-range parameter instead of a routing policy.
Answer: D
certification Juniper JN0-694 JN0-694
NO.7 Your Layer 2 network uses VLAN IDs 100 through 400 and you are required to load-balance
these VLANs between two different root bridges. You are currently using the default RSTP settings
and notice that all VLANs are using the same root bridge.
How do you ensure the VLANs are load-balanced between two root bridges?
A. Configure MSTP with two MSTI regions and split the VLAN range between them.
B. Configure VSTP with two VLAN groups and split the VLAN range between them.
C. Configure two RSTP instances and split the VLAN range between them.
D. Configure STP and RSTP and split the VLAN range between them.
Answer: A
Juniper JN0-694 examen JN0-694 JN0-694 examen certification JN0-694
NO.8 Two neighboring routers are able to form an OSPF adjacency, but are not able to establish an
IBGP neighborship.
What are two reasons for the IBGP neighborship problem? (Choose two.)
A. One of the devices has a misconfigured BGP peer address.
B. One or both of the connected interfaces are missing the family iso statement.
C. OSPF has a lower route preference than BGP .
D. A firewall filter on one of the interfaces is blocking TCP traffic.
Answer: B,C
Juniper JN0-694 examen JN0-694 examen JN0-694 JN0-694
Un bon choix de l'outil à se former est le point essentiel à passer le test Juniper JN0-694, et les documentations à propos de rechercher le test Juniper JN0-694 est toujours une part plus importante pendant la préparation de test Certification. Les Q&As offertes par les experts de Pass4Test sont presque même que les tests réels. Pass4Test est un site web particulièrement en apportant les facilités aux gens qui veulent passer le test Certification.
没有评论:
发表评论