Juniper JN0-694, de formation et d'essai

Au 21er siècle, il manque encore grand nombreux de gens qualifié de IT. Le test Certificat IT est une bonne façon à examiner les hommes de talent. Ce n'est pas un test facile à réussir. Un bon choix de formation est une assurance pour le succès de test. Le test simulation est bien proche que test réel. Vous pouvez réussir 100%, bien que ce soit la première à participer le test.

Le test simulation offert par Pass4Test est bien proche du test réel. Vous pouvez apprendre tous essences d'un test réel à courte terme avec l'aide de Pass4Test. Pass4Test peut vous assurer le succès 100% de test Juniper JN0-694.

Pass4Test est un fournisseur important de résume du test Certification IT dans tous les fournissurs. Les experts de Pass4Test travaillent sans arrêt juste pour augmenter la qualité de l'outil formation et vous aider à économiser le temps et l'argent. D'ailleur, le servie en ligne après vendre est toujours disponible pour vous.

Code d'Examen: JN0-694
Nom d'Examen: Juniper (Enterprise Routing and Switching Support, Professional (JNCSP-ENT))
Questions et réponses: 36 Q&As

La Q&A Juniper JN0-694 de Pass4Test est liée bien avec le test réel de Juniper JN0-694. La mise à jour gratuite est pour vous après vendre. Nous avons la capacité à vous assurer le succès de test Juniper JN0-694 100%. Si malheureusement vous échouerez le test, votre argent sera tout rendu.

Vous pouvez télécharger tout d'abord une partie de Q&A Certification Juniper JN0-694 pour tester si Pass4Test est vraiment professionnel. Nous pouvons vous aider à réussir 100% le test Juniper JN0-694. Si malheureusement, vous ratez le test, votre argent sera 100% rendu.

JN0-694 Démo gratuit à télécharger: http://www.pass4test.fr/JN0-694.html

NO.1 Two neighboring routers are able to form an OSPF adjacency, but are not able to establish an
IBGP neighborship.
What are two reasons for the IBGP neighborship problem? (Choose two.)
A. One of the devices has a misconfigured BGP peer address.
B. One or both of the connected interfaces are missing the family iso statement.
C. OSPF has a lower route preference than BGP .
D. A firewall filter on one of the interfaces is blocking TCP traffic.
Answer: B,C

Juniper examen   JN0-694   JN0-694

NO.2 Your switch is experiencing a problem where a port that should have only one host connected
occasionally shows that multiple MAC addresses are being learned.
Which configuration setting would ensure that no extra hosts can join the network using this switch
port?
A. mac-limit
B. no-mac-learning
C. persistent-learning
D. bpdu-block-on-edge
Answer: D

Juniper examen   certification JN0-694   JN0-694   JN0-694   JN0-694 examen

NO.3 You are having problems redistributing RIP routes into OSPF. Your Junos device has the
following configuration:
[edit protocols ospf]
user@router# show
import my-policy;
area 0.0.0.0 {
interface ge-0/ 0/ 0.0;
interface ge-0/ 0/ ;
interface ge-0/ 0/ {
passive;
}
}
What would resolve the problem?
A. Apply my-policy as an export policy under the [edit protocols rip] hierarchy.
B. Apply my-policy as an import policy under the [edit protocols rip] hierarchy.
C. Apply my-policy as an export policy under the [edit protocols ospf] hierarchy.
D. Use the area-range parameter instead of a routing policy.
Answer: D

certification Juniper   JN0-694   JN0-694 examen   JN0-694 examen

NO.4 You are troubleshooting a problem where an OSPF adjacency between two neighboring
routers will not form.
What are two reasons for this problem? (Choose two.)
A. One or both of the connected interfaces are missing the family inet statement.
B. One or both of the connected interfaces are missing the family iso statement.
C. The connected interfaces are not on the same subnet.
D. Another IGP is running on one or both of the routers, overriding OSPF.
Answer: B,D

Juniper   JN0-694   certification JN0-694   JN0-694 examen   JN0-694

NO.5 You observe that a router is using an unusually high amount of CPU cycles.
You determine that continuous SPF calculations in OSPF are being performed.
What are two reasons for this problem? (Choose two.)
A. The wrong authentication keys between the OSPF neighbors are used.
B. The interface MTU is mismatched between the OSPF neighbors.
C. There are duplicate router IDs within the OSPF area.
D. An OSPF adjacency is flapping.
Answer: C,D

certification Juniper   JN0-694   JN0-694   JN0-694

NO.6 Your Layer 2 network uses VLAN IDs 100 through 400 and you are required to load-balance
these VLANs between two different root bridges. You are currently using the default RSTP settings
and notice that all VLANs are using the same root bridge.
How do you ensure the VLANs are load-balanced between two root bridges?
A. Configure MSTP with two MSTI regions and split the VLAN range between them.
B. Configure VSTP with two VLAN groups and split the VLAN range between them.
C. Configure two RSTP instances and split the VLAN range between them.
D. Configure STP and RSTP and split the VLAN range between them.
Answer: A

Juniper   JN0-694   certification JN0-694   JN0-694   JN0-694 examen

NO.7 Your Junos device is dropping certain traffic flows, while allowing other traffic flows to pass
through the device unaffected.
Which CoS component is causing this problem?
A. BA classification
B. RED
C. MF classification
D. Rewrite rules
Answer: D

Juniper   JN0-694   certification JN0-694   JN0-694 examen

NO.8 You are implementing Q-in-Q tunneling on an EX Series switch. You want the tunnel to support
all C-VLANs; however, only some VLANs are able to send traffic across the tunnel.
Switch-1 has the following configuration:
[edit vlans]
user@Switch-1# show
v100 {
vlan-id 100;
interface {
ge-0/ 0/ 0.10;
ge-0/ 0/1.20;
}
dot1q-tunneling {
customer-vlans [ ];
}
}
What would solve this problem?
A. Add family ethernet-switching to the tunnel-side interface on Switch-1.
B. Implement RSTP .
C. Q-in-Q tunneling will not work in this scenario; use a Layer 2 VPN instead.
D. Remove the customer-vlans statement.
Answer: C

Juniper examen   JN0-694 examen   JN0-694 examen   certification JN0-694

L'équipe de Pass4Test rehcerche la Q&A de test certification Juniper JN0-694 en visant le test Juniper JN0-694. Cet outil de formation peut vous aider à se préparer bien dans une courte terme. Vous vous renforcerez les connaissances de base et même prendrez tous essences de test Certification. Pass4Test vous assure à réussir le test Juniper JN0-694 sans aucune doute.