Différentes façons peuvent atteindre le même but, ça dépend laquelle que vous prenez. Beaucoup de gens choisissent le test Cisco 642-883 pour améliorer la vie et la carrière. Mais tous les gens ont déjà participé le test Cisco 642-883, ils savent qu'il est difficile à réussir le test. Il y a quelques dépensent le temps et l'argent, mais ratent finalement.
Généralement, les experts n'arrêtent pas de rechercher les Q&As plus proches que test Certification. Les documentations offertes par les experts de Pass4Test peuvent vous aider à passer le test Certification. Les réponses de nos Q&As ont une précision 100%. C'est facile à obtenir le Certificat de Cisco après d'utiliser la Q&A de Pass4Test. Vous aurez une space plus grande dans l'industrie IT.
Il y a beaucoup de gans ambitieux dansn l'Industrie IT. Pour monter à une autre hauteur dans la carrière, et être plus proche du pic de l'Industrie IT. On peut choisir le test Cisco 642-883 à se preuver. Mais le taux du succès et bien bas. Participer le test Cisco 642-883 est un choix intelligent. Dans l'Industrie IT de plus en plus intense, on doit trouver une façon à s'améliorer. Vous pouvez chercher plusieurs façons à vous aider pour réussir le test.
Le guide d'étude de Pas4Test comprend l'outil de se former et même que le test de simulation très proche de test réel. Pass4Test vous permet de se forcer les connaissances professionnelles ciblées à l'examen Certification Cisco 642-883. Il n'y a pas de soucis à réussir le test avec une haute note.
Code d'Examen: 642-883
Nom d'Examen: Cisco (Deploying Cisco Service Provider Network Routing (SPROUTE) )
Questions et réponses: 82 Q&As
Le suucès n'est pas loin de vous une fois que vous choisissez le produit de Q&A Cisco 642-883 de Pass4Test.
La population de la Certification Cisco 642-883 est très claire dans l'Industrie IT. Pass4Test se contribue à vous aider à réussir le test, de plus, un an de la mise à jour gratuite pendant est gratuite pour vous. Pass4Test sera le catalyseur de la réalisation de votre rêve. Pour le succès demain, Pass4Test est votre von choix. Vous serez le prochain talent de l'Indutrie IT sous l'aide de Pass4Test.
L'équipe de Pass4Test rehcerche la Q&A de test certification Cisco 642-883 en visant le test Cisco 642-883. Cet outil de formation peut vous aider à se préparer bien dans une courte terme. Vous vous renforcerez les connaissances de base et même prendrez tous essences de test Certification. Pass4Test vous assure à réussir le test Cisco 642-883 sans aucune doute.
642-883 Démo gratuit à télécharger: http://www.pass4test.fr/642-883.html
NO.1 Refer to the PE1 router routing table output exhibit.
What is causing the i su 10.1.10.0/24 [115/30] via 0.0.0.0, 00:40:34, Null0 entry on the PE1 router routing
table?
A. The PE1 router is receiving the 10.1.10.0/24 summary route from the upstream L1/L2 IS-IS router.
B. The PE1 router has been configured to summarize the 10.1.10.x/32 IS-IS routes to 10.1.10.0/24.
C. The 10.1.10.0/24 has been suppressed because IS-IS auto-summary has been disabled on the PE1
router.
D. The 10.1.10.0/24 has been suppressed because of a route policy configuration on the PE1 router.
E. The 10.1.10.0/24 has been suppressed because the more specific 10.1.10.x/32 IS-IS routes have
been configured to leak into the IS-IS non-backbone area.
Answer: B
Cisco 642-883 642-883 examen certification 642-883 certification 642-883
NO.2 On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF
in area 0?
A. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0
B. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 255.255.255.255
area 0
C. router ospf 1 area 0 interface GigabitEthernet0/0/0/1
D. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ip ospf 1 area 0
E. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0
F. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0
Answer: C
Cisco 642-883 certification 642-883 certification 642-883
NO.3 Which three statements are true regarding the OSPF router ID? (Choose three.)
A. The OSPF routing process chooses a router ID for itself when it starts up.
B. The router-id command is the preferred procedure to set the router ID.
C. If a loopback interface is configured, its address will always be preferred as the router ID over any
other methods.
D. After the router ID is set, it does not change, even if the interface that the router is using for the router
ID goes down. The router ID changes only if the router reloads or if the OSPF routing process restarts.
E. In OSPF version 3, the OSPF router ID uses a 128-bit number.
Answer: A,B,D
Cisco 642-883 certification 642-883 642-883
NO.4 Which four statements are correct regarding IS-IS operations? (Choose four.)
A. By default, Level 1 routers within an IS-IS area do not carry any routing information external to the area
to which they belong. They use a default route to exit the area.
B. Summarization should be configured on the Level 2 routers, which injects the Level 2 routes into Level
1.
C. IS-IS supports "route leaking" in which selected Level 2 routes can be advertised by a Level 1/Level 2
router into Level 1.
D. The IS-IS backbone is a contiguous collection of Level 1 capable routers, each of which can be in a
different area.
E. With IS-IS, an individual router is in only one area, and the border between areas is on the link that
connects two routers that are in different areas.
F. Cisco IOS XR Software supports multitopology for IPv6 IS-IS unless single topology is explicitly
configured in IPv6 address-family configuration mode.
Answer: A,C,E,F
Cisco 642-883 642-883 642-883
NO.5 Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)
A. to connect an OSPF non-backbone area to area 0 through another non-backbone area
B. to connect an NSSA area to an external routing domain
C. to connect two parts of a partitioned backbone area through a non-backbone area
D. to enable route leaking from Level 2 into Level 1
E. to enable route leaking from Level 1 into Level 2
F. to enable OSPF traffic engineering
Answer: A,C
Cisco 642-883 examen certification 642-883 642-883 examen 642-883
NO.6 Refer to the OSPF command exhibit.
Which effect does the no-summary command option have?
A. It will cause area 1 to be able to receive non-summarized inter-area routes.
B. It will cause area 1 to not receive any inter-area routes and will use a default route to reach networks in
other areas.
C. It will cause area 1 to not receive any external routes and will use a default route to reach the external
networks.
D. It will convert the NSSA area into a NSSA totally stubby area.
E. It will convert the stubby area into a NSSA.
F. It will disable OSPF auto-summary.
Answer: B
certification Cisco certification 642-883 642-883
NO.7 In comparing IS-IS with OSPF, a Level-1-2 IS-IS router is similar to which kind of OSPF router?
A. ASBR on a normal OSPF area
B. ASBR on NSSA
C. ABR on totally stubby OSPF area
D. ABR on stubby OSPF area
E. ABR on a normal OSPF area
Answer: C
Cisco certification 642-883 certification 642-883 certification 642-883
NO.8 When troubleshooting OSPF neighbor errors, which three verification steps should be considered.?
(Choose three.)
A. Verify if neighboring OSPF interfaces are configured in the same area.
B. Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
C. Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
D. Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
E. Verify if neighboring OSPF interfaces are configured with the same area type.
Answer: A,D,E
Cisco 642-883 certification 642-883 642-883 examen
NO.9 What is function of the RP/0/RSP0/CPU0:PE1(config-ospf)#distance Cisco IOS-XR command?
A. To modify the administrative distance of the OSPF routes
B. To modify the default seed metric of the OSPF external routes
C. To modify the OSPF default reference bandwidth
D. To modify the OSPF cost
Answer: A
Cisco certification 642-883 642-883 examen 642-883 642-883 examen
NO.10 When configuring IPv4 and IPv6 IS-IS routing on Cisco IOS XR routers, which three statements are
correct? (Choose three.)
A. By default, a single SPF is used for both IPv4 and IPv6, so the IPv4 and IPv6 topology should be the
same.
B. By default, the IS-IS router type is Level 1 and Level 2.
C. All IS-IS routers within the same IS-IS area must be configured with the same IS-IS routing process
instance ID.
D. By default, metric-style narrow is used.
E. By default, the IS-IS interface circuit type is Level 1 and Level 2.
F. The area IS-IS address-family configuration command is used to specify the IS-IS area address.
Answer: B,D,E
Cisco examen 642-883 642-883 certification 642-883
Dans ce monde d'informatique, l'industrie IT est suivi par de plus en plus de ges. Dans ce domaine demandant beaucoup de techniques, il faut des Certificat à se preuver les techniques professionnelle. Les Certificats IT sont improtant pour un interviewé pendant un entretien. C'est pas facile à passer le test Cisco 642-883, donc c'est pourquoi beaucoup de professionnels qui choisissent ce Certificat pour se preuver.
没有评论:
发表评论